QC Lab TechnicianMetromont
Job Summary
JOB OUTLINE
LOCATION:
Hiram
TITLE / POSITION:
QC Lab Technician
DEPARTMENT:
QUALITY CONTROL
SUPERVISOR(S):
TERRY SNOW
REVIEW DATE:
02/19/09
Climbing: n/a
Repetitive Motion / Force: 5%
% based on a 10 hour shift
PHYSICAL REQUIREMENTS:
Lifting / Lbs: 40% / 50-75lbs
Bending: 40%
Pushing / Pulling: 10%
Standing / Walking: 100%
Twisting: 30%
PPE REQUIRED: Gloves, hard hat, Steel toe boots, Safety Glasses, Ear plugs, High visibility vest, At time and for certain tasks, elbow length gloves.
EQUIPMENT / TOOLS: Cylinder tanks, Hammer, Chipping Hammer, Scrapper, Margin trowel, Water Brush, Hand Float, Computer
SKILLS REQUIRED: Advanced Reading, writing and math skills, able to read a tape measure to 1/16th, Basic Blue print and plans reading, Computer literate with experience in Excel, Précis with measurements, Accurate with data recording, very detail orientated to meet minimal specification with precision.
LOCATION : Map code
Indoor/sheltered ( )
Outdoor/non sheltered ( X )
HOURS: 8am – 4pm Mon-Fri
DESCRIPTION OF DUTIES:
Collect and remove from mold test specimens from previous day
Remove cylinders that needed to be broken down for curing tanks
Perform aggregates (rock /Sand) radiations which includes put test sample in oven and dry, run through splitter, weigh, put in shaker, weigh each breakdown and enter data in system.
Make 12x12 color samples as needed
Break tank specimens after drying, record breaks in system
Assist in testing wet concrete ( air, slump, temperature, and unit weight)
Make test specimens9cylinders0 as needed
Must work as part of a team
Actively participate in companies “6S”, “Lean” and Safety Programs
TRAINING: General Safety Orientation, BMP Training, E.A.P, Electrical Safety awareness, Forklift certification, Haz Com, Overhead Crain Training, P.T. , Respirator, PFT & Fit testing, S.W.SP.O.O. , Safe lifting procedures, Torch Safety Training, Specialty QC Equip samples & breaks, PCI & ACI certification
PROGRESSION: Pre Pour/ Post Pour Inspector
This job description is NOT intended to be all inclusive.
Employee may perform other related duties as needed to meet the ongoing needs of the facility.
APPROVED BY:
HR:
SAFETY:
PLANT:
LOCATION:
Hiram
TITLE / POSITION:
QC Lab Technician
DEPARTMENT:
QUALITY CONTROL
SUPERVISOR(S):
TERRY SNOW
REVIEW DATE:
02/19/09
Climbing: n/a
Repetitive Motion / Force: 5%
% based on a 10 hour shift
PHYSICAL REQUIREMENTS:
Lifting / Lbs: 40% / 50-75lbs
Bending: 40%
Pushing / Pulling: 10%
Standing / Walking: 100%
Twisting: 30%
PPE REQUIRED: Gloves, hard hat, Steel toe boots, Safety Glasses, Ear plugs, High visibility vest, At time and for certain tasks, elbow length gloves.
EQUIPMENT / TOOLS: Cylinder tanks, Hammer, Chipping Hammer, Scrapper, Margin trowel, Water Brush, Hand Float, Computer
SKILLS REQUIRED: Advanced Reading, writing and math skills, able to read a tape measure to 1/16th, Basic Blue print and plans reading, Computer literate with experience in Excel, Précis with measurements, Accurate with data recording, very detail orientated to meet minimal specification with precision.
LOCATION : Map code
Indoor/sheltered ( )
Outdoor/non sheltered ( X )
HOURS: 8am – 4pm Mon-Fri
DESCRIPTION OF DUTIES:
Collect and remove from mold test specimens from previous day
Remove cylinders that needed to be broken down for curing tanks
Perform aggregates (rock /Sand) radiations which includes put test sample in oven and dry, run through splitter, weigh, put in shaker, weigh each breakdown and enter data in system.
Make 12x12 color samples as needed
Break tank specimens after drying, record breaks in system
Assist in testing wet concrete ( air, slump, temperature, and unit weight)
Make test specimens9cylinders0 as needed
Must work as part of a team
Actively participate in companies “6S”, “Lean” and Safety Programs
TRAINING: General Safety Orientation, BMP Training, E.A.P, Electrical Safety awareness, Forklift certification, Haz Com, Overhead Crain Training, P.T. , Respirator, PFT & Fit testing, S.W.SP.O.O. , Safe lifting procedures, Torch Safety Training, Specialty QC Equip samples & breaks, PCI & ACI certification
PROGRESSION: Pre Pour/ Post Pour Inspector
This job description is NOT intended to be all inclusive.
Employee may perform other related duties as needed to meet the ongoing needs of the facility.
APPROVED BY:
HR:
SAFETY:
PLANT:
